Humidity Sensor Hr002 for Air Control System

• Customization: Available
• Installation Type: Duct Type
• Sensing Type: Thermocouple
• Model NO.: HR002
• Contact: Contactless
• Output Signal Type: Digital Type
• Production Process: Integration
• Material: Carbon Humidity
• Measuring Medium: Humidity
• IP Rating: IP20
• Certification: CE
• Customized: Customized
• Transport Package: 1000PCS in One Pack
• Specification: 100000pcs in one carton
• Trademark: HW
• Origin: Guangdong, China
• HS Code: 8421991000
• Production Capacity: 100000PCS/Week

Product Description

1. Product introduction:

The product is called resistance type polymer humidity sensor (HR002) and it is a new type of humidity sensor. It has the characteristics of wide sensing range, fast response, high sensitivity, good water resistance, stable and reliable performance, and good consistency.


2.Electrical performance:
1. Rated voltage: 1.5V AC (MAX, sine wave);
2. Rated power: 0.2mW (MAX, sine wave);
3. operating frequency: 50Hz-2000Hz;
4. working temperature: 0 °C -60 °C;
5. working humidity: 20% - 95% RH;
6. Temperature characteristics: ≤0.5%RH/°C
7. hysteresis hysteresis: ≤ 2% RH;
8. Response time: moisture absorption, ≤15S; dehumidification ≤25S;
9. Stability: ≤ 2% RH/year;
10. Humidity detection accuracy: ≤±5%RH;
11. Relative humidity impedance characteristics: (25°C, 1KHZ, AC1V, sine wave)
 

3.Standard verification conditions:

1.In the atmosphere, the temperature is 25°C, the measured frequency is 1KHZ, and the measured voltage is IVAC (sine wave);
2.Make sure to use AC bridge (LCR) when testing, and do not use DC power supply;
3.Use split-type humidity generator (HX-1 type);
4.Measurement line: 1-core shielded wire.
5.Avoid hard objects or fingers touching the surface of components to avoid scratching or staining the wet film;
6.Avoid testing under salt spray, corrosive gases, strong acids, strong bases, organic solvents, alcohol, acetone, etc.
7.Welding conditions (180°C, 3S) For welding, use a low-temperature soldering iron or use tweezers for protection.
8.Recommended Storage Conditions: Temperature 10°C-40°C, Humidity: 20%RH-90%RH.


The specification value is based on the 60%RH humidity change amount; after each test is completed, it should be placed in the normal air of normal temperature and humidity for 24 hours and tested after recovery. The test data are listed in the table.   

1-Exported feet  2-Substrates  3-Carbon Electrodes  4-Sensitive Wet Film
Figure 1 (1008) dimensions



Table 1 Humidity Impedance Characteristics Table at 0°C to 60°C (31KΩ)

	0ºC	5ºC	10ºC	15ºC	20ºC	25ºC	30ºC	35ºC	40ºC	45ºC	50ºC	55ºC	60ºC
20%RH				2290	1759	1351	1027	780	591	448	359	288	227
25%RH		2100	1620	1250	935	700	539	415	328	260	218	183	149
30%RH	1543	1175	874	650	498	382	302	238	198	165	143	124	94
35%RH	832	612	465	353	277	217	180	150	128	109	90.4	75	61.8
40%RH	443	335	260	202	165	135	114	97	81.2	68	59.5	52	43.6
45%RH	248	190	153	123	105	90	76.5	65	55.6	47.5	41.9	37	31.3
50%RH	146	115	98.9	85	72	61	52.4	45	39.1	34	30.1	26.7	22.7
55%RH	94	80	68.1	58	49.9	43	37.1	32	28	24.5	21.9	19.5	15.6
60%RH	64.3	56	48.2	41.5	35.9	31	26.6	22.9	20.2	17.8	15	12.6	10
65%RH	45.9	41	35.1	30	25.9	22.3	19.2	16.5	13.8	11.6	9.6	7.9	6.45
70%RH	33.4	30	25.6	21.9	18.7	15.9	13.1	10.8	9	7.5	6.2	5.13	4.29
75%RH	24.4	21.5	18.3	15.6	12.8	10.5	8.69	7.2	5.95	4.92	4.13	3.46	2.84
80%RH	17.4	15.3	12.6	10.3	8.5	7.03	5.8	4.78	3.98	3.31	2.73	2.25	1.88
85%RH	12	10.2	8.4	6.91	5.67	4.65	3.86	3.2	2.65	2.19	1.81	1.49	1.24
90%RH	7.9	6.87	5.6	4.56	3.77	3.11	2.56	2.11	1.74	1.44	1.19	0.99	0.82

Figure 2 humidity impedance characteristics (31KΩ)

Table 2 0°C to 60°C (23KΩ) Humidity Impedance Characteristics Data Sheet
	0ºC	5ºC	10ºC	15ºC	20ºC	25ºC	30ºC	35ºC	40ºC	45ºC	50ºC	55ºC	60ºC
20%RH				1699.0	1305.1	1002.4	762.0	578.7	438.5	332.4	266.4	213.7	168.4
25%RH		1558.1	1201.9	927.4	693.7	519.4	399.9	307.9	243.4	192.9	161.7	135.8	110.5
30%RH	1144.8	871.8	648.5	482.3	369.5	283.4	224.1	176.6	146.9	122.4	106.1	92.0	69.7
35%RH	617.3	454.1	345.0	261.9	205.5	161.0	133.5	111.3	95.0	80.9	67.1	55.6	45.9
40%RH	328.7	248.5	192.9	149.9	122.4	100.2	84.6	72.0	60.2	50.5	44.1	38.6	32.3
45%RH	184.0	141.0	113.5	91.3	77.9	66.8	56.8	48.2	41.3	35.2	31.1	27.5	23.2
50%RH	108.3	85.3	73.4	63.1	53.4	45.3	38.9	33.4	29.0	25.2	22.3	19.8	16.8
55%RH	69.7	59.4	50.5	43.0	37.0	31.9	27.5	23.7	20.8	18.2	16.2	14.5	11.6
60%RH	47.7	41.5	35.8	30.8	26.6	23.0	19.7	17.0	15.0	13.2	11.1	9.3	7.4
65%RH	34.1	30.4	26.0	22.3	19.2	16.5	14.2	12.2	10.2	8.6	7.1	5.9	4.8
70%RH	24.8	22.3	19.0	16.2	13.9	11.8	9.7	8.0	6.7	5.6	4.6	3.8	3.2
75%RH	18.1	16.0	13.6	11.6	9.5	7.8	6.4	5.3	4.4	3.7	3.1	2.6	2.1
80%RH	12.9	11.4	9.3	7.6	6.3	5.2	4.3	3.5	3.0	2.5	2.0	1.7	1.4
85%RH	8.9	7.6	6.2	5.1	4.2	3.5	2.9	2.4	2.0	1.6	1.3	1.1	0.9
90%RH	5.9	5.1	4.2	3.4	2.8	2.3	1.9	1.6	1.3	1.1	0.9	0.7	0.6

Figure 3 Humidity Impedance Characteristic Diagram (23KΩ)