Pyroelectric Infrared Sensor P914 Digital PIR Infrared Sensor for Human Detector for Motion Sensor

• Customization: Available
• Type: Probe
• Usage: Anti-theft, Temperature, LED Light
• Model NO.: P914
• Installation Mode: Wall Mounted
• Application: Home, Industry, Communication Electronic Products, Special Equipment, Traffic
• Input: 3.3V
• Output: Digital
• Pin: 4
• Transport Package: Standard Package
• Specification: 6000pcs/carton
• Trademark: HW
• Origin: China
• Production Capacity: 1000000/Month

Product Description

Pyroelectric infrared sensor P914 Digital PIR infrared  Sensor for human detector for motion sensor

1. 1.  FEATURES

High sensitivity and superior SNR(signal-to noise ratio)


High stability for temperature change


High anti-interference ability (For example: vibration, radio frequency interference)

1. 1.  APPLICATIONS

Security

Luminaire

 Family and other fields

1. 1.  APPLICATIONS  RANGE

This specification describes a pyroelectric passive infraredsensor for passive infrared sensor device.

1. 1. TYPE OF SENSOR

Balanced differential type (Series opposed type.)

1. 1. APPEALANCE AND DIMENSIONS

1. 1. VISUAL INSPECTION

There are not remarkable wounds,spots,rust and etc.

1. 1. APPEALANCE AND DIMENSIONS

TO-5:
TO-5 Package: see fig 1.

 

1. 1.  ELECTRICAL CHARACTERISTICS( AT 25ºC )

 

ITEM	CONDITION	RATING
6.1 Signal Output	Black Body temperature: 420K 1HZ, 0.3~ 3.5HZ △f Chopping Frequency: 1HZ, 0.3~ 3.5HZ △f Vd=5V,Rs=47KΩ,72.5 Db Vd=5V,Rs=47KΩ,the amplifier of Gain 72.5dB Measurement method shown in Fig2.	>6500mVp-p
6.2 Noise Output	1HZ, 0.3~ 3.5HZ △f Chopping Frequency: 1HZ, 0.3~ 3.5HZ △f Vd=5V,Rs=47KΩ, 72.5 Db Vd=5V,Rs=47KΩ,the amplifier of Gain 72.5dB Measurement method shown in Fig2.	< 140mVp-p
6.3 Balance output	Black Body temperature: 420K 1HZ, 0.3~ 3.5HZ △f Chopping Frequency: 1HZ, 0.3~ 3.5HZ △f Vd=5V,Rs=47KΩ, 72.5 Db Vd=5V,Rs=47KΩ,the amplifier of Gain 72.5dB Measurement method shown in Fig2 and Fig3. S1 = A+C (Vp-p)      S1 = A+C Element sensitivity (Vp-p) S2 = B+D (Vp-p) S2 = B +DElement sensitivity (Vp-p)	|S1-S2|/(S1+S2) ×100%≤15%
6.4 Operating Voltage	Single power supply RS=47KΩ	2~15V
6.5 Source Voltage	VD=5V,RS=47KΩ	0.4~1.0V
6.6 Circuit Configuration	See Fig.4
6.7 Warm-up Time	After it conneted, it with the measurement amplifier for Fig.3 description that turns on the power supply beforehand, the amplification output is time until stabilizing.	Max: 25 Sec

 

1. 1.  OPTICAL CHARACTERISTICS

 

ITEM	RATING
7.1	115 degrees from center of Element on Axis X.
Field of View	110 degrees from center of Element on Axis Y.
	See Fig 5
7.2 Response wavelength band	Filter substrate:Silicon Cut on wavelength:5.5±0.5μm Transmission:7~14μm ≥75%
7.3 Transmission Characteristics of filter	See Fig 6

 

1. 1.  ENVIRONMENTAL REQUIREMENTS

 

ITEM	RATING
8.1 Operating Tmeperature	-30~70 ºC
8.2 Storage Temperatur	-40~80 ººC
8.3 Relative Humidity	The sensor shall operate without increase in Noise Output when exposed to 90 to 95% RH at 30ºC continuously
8.4 Hermetic Seal	No bubbles visible in the 125±5ºC fluorocarbon bath(FC-40) for 20sec
8.5 Reliability Test	Specified in Appendix1( page13~14)

 

1. 1.  ROHS COMPLIANCE

This product conforms to RoHS regulatin.
 

1. 1. INSPECTION

1. 1. Process inspection

100% inspection: Item 6.1 to 6.3 and 6.5 among the electric performances of item 6.

 

1. 1.  OUTGOING INSPECTION

Based on statistical sampling inspection method every manufacture lot is inspected for the electrical characteristics item 6.1to 6.3 ,6.5 of the Item 6,and item 5.1 and 5.3 of the appearance of item 5.

1. 1. PACKING

The packaging is solid and there isn't breakage

1. 1. PROCESS ATFAILURE

In case of finding of failure incoming or process inspection after receipt of products, Both sides negotiate to deal with the failure

1. 1.  PRODUCTION GROUND

China

1. 1.  REVISION

Any revision of this specification should be made in writing by discussion.