Hw-Hy003 Flame Alarm Sensor Module--Two Probe

Product Description

Product Description

 

1.Product Overview

HW-HY003 is the company's latest single-board thermal radiation flame alarm sensor module. The passive single sensor detection adopts: thermal radiation induction judgment method, using the Curie temperature of lithium carbonate crystal material, for flame temperature 250-4000ºC and above, wavelength 380-750nm flame accurate detection and warning. The relative dielectric constant is small, and within a wide range of room temperature, for fire warning, there can be obvious temperature difference high contrast polarity changes, the detector performance is stable, when a fire occurs, it can quickly capture the response to trigger an alarm within 1 to 2 seconds, and is used for various types of open flame induction fire warnings: fire warning, security warning, industrial plants, mining areas, chemical combustible alarms, family residences, charging piles, gas stations, chargers, equipment and machinery, etc.
2.Operational Principle
HW-HY003 is a flame detector using lithium carbonate crystal composite materials. It uses filters to test spectra of different bands to detect visible or invisible light radiation generated when materials burn, while generating smoke and releasing heat. It uses the light characteristics of flames for shorter ultraviolet bands and longer infrared bands. When different materials burn, the red and ultraviolet spectra they emit are different. The environmental spectrum is distinguished from the flame spectrum, thereby causing the sensor electric field phase change and outputting a warning signal.
3.Product Features
HW-HY003 dual-element sensor captures signals with wide coverage, high consistency, low power consumption, and meets the certification requirements of ROHS.CE.KC.UL, etc. It also has strong anti-interference ability and is not affected by ambient temperature, humidity, airflow, dust, noise, brightness, etc. Special anti-interference ability. It can better adapt to the application occasions of the secondary development of most smart products. When this product is used indoors, the sensing effect is better; when used outdoors, due to the influence of the environment, the sensing distance is slightly shortened or the sensitivity is slightly weaker. This is a normal phenomenon, and users do not need to question the product. This product is mostly used in macro scenes.
4.Induction Time
   Fire warning capture time, when the trigger condition is reached, the trigger signal will be output continuously, and the LED indicator will be always on. When the flame disappears, the flame sensor source will reset within 3-5 seconds and resume detection mode. The sensing time is determined by the occurrence of the fire.

Product Parameters

 

5.Parameter Specifications

Model	HY003	Flame alarm module	Single probe short distance 43
VCC	Min:3.3V	Middle value: 5v	Maximum value: 12v (withstand voltage 3.3v-18v-300mA)
V/A	<30mA
OUT-Siginal	TTL signal	AD/SLK DIO serial port signal
Induction method	Passive flame thermal radiation detection
Induction Distance	1-30m	Determined by the heat source coefficient	Thermal radiation proportional coefficient
Blackbody threshold	500k	1HZ 0.3-3BPS	Default 500K
Induction time	Continuous high level when there is fire	Reset within 30 seconds after fire extinguishing
Induction angle	10-110°		Window angle
Sensor wavelength	380-750nm		Flame thermal radiation wavelength (refer to the following text)
Spectral wavelength of filter	(refer to the following text)		Chemical combustible spectrum(refer to the following text)
Size	30mm x26.7x12mm	square
Port	Data output 1.25mm-6pin	Port 1.25mm-3pin
working temperature	-20----+70

6.Product inspection wiring diagram and CAD diagram

As shown in the figure, VIN can supply DC5V, and various identification data interfaces are for the microcontroller to collect signals.
Port J1: The output port is the flame output port and the positive and negative input of the power supply.
Port J2: External serial port data output.
Port J3: Software editing and burning port.
Button SW: Data reset switch.
Later, the J1 port can be used to output a high-level signal. If there is a fire in the detection area, the LED will light up red to alarm, and the LED will flash blue, which is the sentry mode. The red LED will continuously trigger the signal: connect the security fire warning circuit, trigger circuit-MOS tube-thyristor-relay-MCU to collect signals to alarm the occurrence of fire, etc.
CAD Dimensions:

Detailed Photos